 |
|
 |
| |
 Accessories |
| |
| PROTECTIVE MASK with filter |
 |
| |
| SIEVE |
 |
| |
| LANCE |
 For
the IBIX®
9F:
Nozzle lance (1.2 m long) made of special material (ERGAL 70-75),
complete with grip, trigger mechanism, inert material+air hose (6 m
long) and nozzle holder at lance tip.
Recommended where cleaning surfaces that would otherwise be out of
reach or when working from scaffolding (e.g. removal of graffiti up to
head height or cleaning wooden beams, ceilings): allows the user to
keep a safe distance from the surface being cleaned.
For the IBIX® 25P:
Nozzle lance (1.2 m long) made of special material (ERGAL 70-75),
complete with grip, trigger mechanism, inert material+air hose (10 m
long) and nozzle holder at lance tip. Recommended where cleaning
surfaces that would otherwise be out of to reach or when working from
scaffolding (e.g. removal of graffiti up to head height or cleaning
wooden beams, ceilings): allows the user to keep a certain distance
from the surface being cleaned. |
| |
| WATER VAPORIZER
|
|
 The IBIX® DL3K and DL6K VAPORIZER are designed to
reduce the dust caused by projection of very fine, dusty materials. The
IBIX® DL3K
and DL6K stop dust
spreading with the aid of a special nozzle that sprays a fine “bell” of
nebulized water. This bell stops the dust spreading to the surrounding
environment.
The water vaporization nozzle incorporates a special support in which
the IBIX® gun nozzle
is inserted and locked in place with a throttle screw.
The angle between material outflow and water outflow is specially
designed to ensure optimal results.
With the tank full and the tap fully
open the VAPORISER has 40 minutes’ autonomy: the tank holds 9.5 litres
of water.
The IBIX® DL3K VAPORIZER
must be connected to an air compressor: this pressurises the water to a
constant 3 bar and generates a water bell that is uniform, without
generating drops that might compromise the efficiency of the blasting
material.
Open the tap during work and re-close it once work is over.
Low air consumption: a compressor with
an effective air outflow rate of 350 l/min will suffice.
Portability and lightweight plastic allow the Vaporisation System to be
used in difficult-to-reach areas. Moreover, the device is extremely
hard-wearing and does not require maintenance.
The IBIX® DL3K comes
with a 3 m water hose and has been designed for use with the IBIX® 9F Eco-Blaster; the DL6K, instead, has a 6 m hose
and has been designed for use with the IBIX®
25P.
|
| |
| IBIX DWK1 |
|
 Dust abatement accessory for the IBIX® 9F2, DL3K and A90 equipment sets.
The DWK1 is used to wash
blasted surfaces so as to remove any powder residues on facades,
floors, panelling or other aluminium items. The system is autonomous
and does not require connection to the water mains or other complex
equipment. The DWK1, in
fact, has a rapid coupling for connection of the hose to the air
compressor and a wash lance.
Low air consumption: a compressor with an effective air
outflow rate of 350 l/min will suffice.
The portability and lightness of the aluminium-made Wash System allow
it to be used even in difficult-to-reach areas.
Moreover, the device is extremely hard wearing and does
not require maintenance.
|
| |
| SUCTION BRUSH |
 Brush-equipped device for
dust-free blasting. Features an intake port for connection to an
industrial vacuum system.
The blast gun nozzle is positioned inside a special hole
while an ergonomic grip allows the user to hold the device comfortably.
Effective dust / inert blasting material suction
capacity depends on the power of the industrial vacuum system.
Recommended for use on flat horizontal and vertical
surfaces only and where completely uniform cleaning of the surface is
necessary.
|
| |
| BACKPACK |
|
Backpack-type carry harness for IBIX® 9 blaster: allows user
to carry the machine comfortably up and down ladders/scaffolding in
comfort. A must in shipyards/boatyards and for NDT welding inspectors.
|
| |
|
|
| |
SECURITY KIT: tyvek suite - gloves - ear protector -
protective glases
|
|
|
| |
return to MACHINES
 |
| |
|
 |
